BIG 3 OFC Pure Copper cable wire kit upgrade 1/0 AWG GAUGE braided sleeve PREWir

Description

Notes
Do It Yourself Heavy Duty High Output Big 3 Cable Wiring Kit
This kit is a must to obtain the highest electrical output from your alternator and your battery and to professionally ground your electrical system to your car chassis/Trans/Engine
Made in the USA
Ready to ship via Priority Mail
Welding cable is the best cable for highest possible electrical current
This welding wire is true to spec (AWG) and it is very heavy, however, still very flexible
Three of the six cable lugs are crimp to the cables
Three of the six heat shrink tubes are pre-glued to the cables
These cables are covered with braided sleeves
This kit includes:
4 ft. 1/0 AWG Premium Extra Flexible Welding Cable 600 VOLT - Red - EWCS Spec
4 ft. Flexo PET Expandable Braided Sleeving – Blackred (pre-installed)
8 ft (2 rolls of 4 ft., you can request one roll of 8 ft instead) 1/0 AWG Premium Extra Flexible Welding Cable 600 VOLT - Black - EWCS
8 ft. Flexo PET Expandable Braided Sleeving – Blackblue (pre-installed)
3 ea. 1/0 AWG 5/16" stud. Premium Tinned Battery Cable Lugs by FTZ (FTZ are the best lugs in the market)
3 ea. 1/0 AWG 5/16" stud. Premium Tinned Battery Cable Lugs by FTZ which are crimp (pre-wired) to the cables
1 ea.
TEMCo Red 3/4" Glue Lined Marine Heat Shrink Tube 3:1 Adhesive (marine quality to prevent corrosion from water)
1 ea.
TEMCo Red 3/4" Glue Lined Marine Heat Shrink Tube 3:1 Adhesive which is pre-glued to the cable
2 ea. TEMCo Black 3/4" Glue Lined Marine Heat Shrink Tube 3:1 Adhesive (marine quality to prevent corrosion from water)
2 ea. TEMCo Black 3/4" Glue Lined Marine Heat Shrink Tube 3:1 Adhesive which are pre-glued to the cable
Shipping
Your order will be processed within 2 business days after your payment.
Shipping will be via Priority Mail.
Transit time varies from 2-5 business days.
We only ship within the continental USA, we do
not
ship to Alaska, Hawaii, Puerto Rico, APO addresses or any other USA territory.
We only ship to the confirmed Paypal address.  We reserve the right to cancel any order for any reason at any time.
We are not responsible for undeliverable addresses.
Payments & Terms
We accept PayPal payment only.
Please make sure your paypal and ebay address is correct.  Or not, please correct it before payment.
No international shipping
Returns & Exchanges
We gladly accept returns and exchanges within 14 days under the following conditions:
All items have to be in the same exact condition as to when they were shipped.
The components should have not been damaged or altered in any way or form.
20% restocking fee applies to all Returns and buyer pays for the return shipping
20% exchange fee applies to all Exchanges and buyer pays for the return shipping
Special Notes
Only use 1/0 gauge wire rated at 600 volts for High Output Alternator/battery installation
It is extremely recommended that you do not exceed 18 inches in length in the wire between the battery and the fuse holder/blocker
Recommended to only use Tin plated Copper lugs since non-tin plated copper lugs are easily prone to corrosion
Only use Glue Line Marine Quality Heat Shrink tubing to prevent corrosion from humidity/water
Battery Cable & Wire Features:
Made in the USA
Polyvinyl-chloride (PVC) insulation
-50°C MTW - UL & CSA 105°C
Voltage rating: 600 volts
VW-1 & moisture resistant
Heat Shrink Features:
Shrink ratio: Approximately 3 to1 at +90°C
Operational temp. range: -55°C to +135°C
Dielectric strength: 500 V/mil (197 kV/cm)
Volume resistivity: 1014 ohm-cm
Tensile strength: 1500 psi (141 kg/cm2)
Ring Terminal Features:
Seamless Tubular Barrel
Non-Insulated
Tin-Plated Copper
Made in the USA
Flexo PET Expandable Braided Sleeving
Operating temp(degree F.):-103 to 257|Melt temp: 446.Our braided cable sleeve is used in automotive Hifi audio speaker hdmi wire
Our PET expandable braided sleeving : UL | ROHS | REACH | Halogen Free
Our cable sleeving protects and prolongs the life of wires.
Recommended: Cut Braided Sleeving with a HOT KNIFE to prevent fraying, if a Hot Knife is not available, make sure to sear the edges with another heat source (example: use the flame from a lighter)